# if isDA is false.
;net.slp.DAHeartBeat = 10800
+# A 32 bit integer giving the number of seconds after which a DA is considered
+# stale and is removed from the list of known DAs, if a DA advert has not
+# been received for it. This value affects DAs in that it overrides
+# net.slp.DAHeartBeat to ensure that DA adverts are sent out at an appropriate
+# rate dependent on this value. It affects SA operation, in that heartbeats
+# (DA adverts) are monitored to maintain only active DAs in the known DA list.
+# Default is 0 (disabled). A minimum of 60s will be applied if non-zero.
+;net.slp.staleDACheckPeriod = 60
#----------------------------------------------------------------------------
# SA Specific Configuration
# If net.slp.watchRegistrationPID is set to true, local registrations made
# with the SA via the SLPReg() API call will be monitored. If the PID of the
# process (and/or thread on Linux) disappears (the registering process died
-# unexpectedly with out calling SLPDereg()), then the registration is
-# automatically de-registered. (Default value is true. Uncomment the line
+# unexpectedly without calling SLPDereg()), then the registration is
+# automatically de-registered. Default value is true. Note that 'slptool'
+# always uses value false for the 'register' command. Uncomment the line
# below to disable PID watching.
;net.slp.watchRegistrationPID = false
;net.slp.maxResults = 256
+# An experimental/test setting that tells libslp to send SLP v1 commands
+# instead of v2 commands where-ever the code currently supports it.
+# Default is false.
+;net.slp.preferSLPv1 = false
+
#----------------------------------------------------------------------------
# Network Configuration Properties
#----------------------------------------------------------------------------
# A value-list of 32 bit integers used as timeouts, in milliseconds, to
# implement unicast datagram transmission to DAs. The nth value gives
# the time to block waiting for a reply on the nth try to contact the DA.
-# Currently OpenSLP uses TCP for all unicast communication so this setting
-# does not do anything
;net.slp.unicastTimeouts = 500,750,1000,1500,2000,3000
# To OpenSLP the following is the same as net.slp.unicastTimeouts. Use
# A integer giving the network packet MTU in bytes. (Default is 1400)
;net.slp.MTU = 1400
-# A list of IP address of network interfaces on which the DA/SA should listen
-# for slp requests. By default, slpd will use all interfaces.
-;net.slp.interfaces = 1.2.3.4,1.2.3.5,1.2.3.6
-
+#
+# If operating as an SA or DA, this specifies the maximum number of interfaces
+# that can be active. (Default is 100)
+;net.slp.max_ifaces = 100
+
+# If operating as an SA or DA, then any local addresses that are going to be
+# used must be specified. Both IPv4 and IPv6 addresses may be specified.
+# Only link-local addresses can be used for IPv6 SLP multicast. Any
+# site-local or global addresses will be used, but only for unicast SLP.
+# Option parameter "%" can be used to specify the interface when multiple
+# instance of the same link-local address are present in the same host. If
+# the interface option is not provided, the daemon will bind to the first
+# interface with specified ip. This option is only valid for IPv6 link-local
+# addresses. Eg: fe80::215:58ff:fe7e:c037%eth0
+;net.slp.interfaces = 192.168.0.1
+
+# This option is a string indicating the broadcast address to use when
+# sending broadcast packets. This parameter is only applicable when the
+# other broadcast configuration variables are set (multicast is used by default)
+;net.slp.broadcastAddr = 255.255.255.255
+
+# Port to use for all SLP messages. Changing this from the reserved SLP
+# listening port will break compliance with RFC2608. (Default is 427).
+;net.slp.port = 427
+
+# A boolean indicating whether DHCP should be used for DA discovery and/or
+# scope discovery. (Default setting is true).
+;net.slp.useDHCP = true
#----------------------------------------------------------------------------
# Security
# address checking.
;net.slp.checkSourceAddr=false
+#----------------------------------------------------------------------------
+# Indexing
+#----------------------------------------------------------------------------
+# A boolean indicating whether SLP service types should be indexed. This
+# uses additional memory, but speeds up searching by (concrete) service type,
+# and attribute retrieval. (Default setting is false).
+;net.slp.indexSrvtype=true
+
+# A list of names of attributes with string values that should be indexed.
+# This uses additional memory but speeds up searching by equality (including
+# wildcard searches)
+# eg. (location=Main Building Second Floor) or (location=Main Building*)
+# The index will also be used when the equality expression is part of a top-level
+# '&' expression eg. (&(grade>=C)(location=Main Building*)) would use
+# the index on the location attribute.
+# Note that whitespace is significant in the list of names.
+;net.slp.indexedAttributes=attr1,attr2,...
#----------------------------------------------------------------------------
# Tracing and Logging
# tracing.
;net.slp.traceMsg = true
+# A boolean controlling whether or not slpd appends log messages to slpd.log,
+# or if it overwrites the existing log. Default is true. Uncomment the
+# following line to overwrite the existing log.
+;net.slp.appendLog = false
#----------------------------------------------------------------------------
# Serialized Proxy Registration
# /etc/slp.reg
+#----------------------------------------------------------------------------
+# IPv6 configuration options
+#----------------------------------------------------------------------------
+# These settings specify which IP protocols to use for SLP. The default is
+# that IPv4 is enabled, and IPv6 is disabled. Uncomment one or other of the
+# following lines to change this.
+;net.slp.useIPv4 = false
+;net.slp.useIPv6 = true
projects / config / bruni / etc.git / commitdiff